亚洲国产精品视频一区二区三区,国产精品久久久久久粉嫩色,欧美日韩国产另类在线,亚洲乱码AV乱码国产精品

山東創圖建筑裝飾工程有限公司 山東創圖建筑裝飾工程有限公司
加工技術熱線:13165128506
  • 您當前位置: 首頁>>新聞動態>>行業動態防火板如何使用以及限制條件

    行業動態

    防火板如何使用以及限制條件

    來源:http://www.kcrft.cn/ 日期:2023-01-30 發布人:admin
    防火板是我們生活中較為常見的板材之一,可以在很多地方派上用場,比如臺面、家具的表面、樓梯的踏步等等。下面來講講防火板如何使用以及限制條件。
    Fireproof board is one of the more common boards in our life, which can be used in many places, such as table tops, furniture surfaces, stairs and so on. Now let's talk about how to use the fireproof board and its restrictions.
    如何使用:
    How to use:
    1.選擇優良基材、粘接使用膠及施工工具。
    1. Select excellent base materials, adhesive and construction tools for bonding.
    a.目前市場常見基材:有細木工板、中纖板、刨花板、密度板,選擇時請注意基材含水量、平整度等參數,特別要選用表面經過砂毛脫膜處理基材;
    A. At present, common substrates in the market include blockboard, MDF, particleboard, and density board. Please pay attention to the moisture content, flatness and other parameters of the substrate when selecting, especially the substrate with sand-like film removal treatment on the surface;
    b.防火板施工史常用的膠有以下幾種:PVAC白膠、NeopreneSolvent強力膠、熱固型樹脂膠、脫水脲醛膠(工業類)、粘貼用膠擇必須選擇正牌優良膠;
    B. The common adhesives used in the construction history of fire-proof board are as follows: PVAC white adhesive, NeopreneSolvent strong adhesive, thermosetting resin adhesive, dehydrated urea-formaldehyde adhesive (industrial type), and the adhesive used for pasting must be selected as the authentic excellent adhesive;
    c.施工工具:由于防火板良地堅硬,所以需要良好品良的工具來配合施工,盡量使用碳鋼制的工具,特別是桌面鋸刀片和修邊機刃,是鋼碳制的,才會有干凈,光滑。沒有缺口的切斷面。使用手工具時候好用有金屬把的手工具,像手動木工鋸(Backsaw)等。
    C. Construction tools: because the fire board is good and hard, it needs good and good tools to cooperate with the construction. Try to use carbon steel tools, especially the table saw blade and trimming machine blade, which are made of steel and carbon, so that they can be clean and smooth. Cut section without notch. When using hand tools, it is better to use hand tools with metal handles, such as manual woodworking saw (Backsaw).
    2.施工過程
    2. Construction process
    a.裁切:將防火板裁切成所需要的尺寸,再沒邊多留1/4英寸(6mm)作為修邊之用,注意鋸齒是從色板的一面進去,這樣才可以避免切斷面產生缺口,若使用刀片切割防火板時,一定要注意同樣也是從色紙的一面進刀,然后像切玻璃一樣的劃下去,才會有干凈,光滑,沒有缺口的切斷面。
    A. Cutting: cut the fireproof board to the required size, and leave 1/4 inch (6mm) more for edge trimming. Pay attention to that the sawtooth enters from one side of the color board, so as to avoid the gap of the cutting section. If you use the blade to cut the fireproof board, you must also pay attention to the cutting from one side of the color paper, and then cut it down like cutting glass, so as to have a clean, smooth, and notch-free cutting section.
    b.涂膠:在防火板背面及基材表面均勻涂上強力膠,如果基材表面非常不平整或吸水性*,手工需上兩次膠以使表面*布膠。施工時注意由于季節、氣候、地區等原因。各強力膠的揮發時間都會有所不同,根據強力膠的使用建議,結合實際操作及施工備件來決定揮發時間,如:使用脫水脲醛膠和白乳膠時,需要在室溫25-30度的條件下加壓十二個小時以上。
    B. Gluing: apply strong glue evenly on the back of the fireproof board and the surface of the base material. If the surface of the base material is very uneven or water absorbent, apply glue twice manually to make the surface * glue. Pay attention to the season, climate, region and other reasons during construction. The volatilization time of each brand of super glue will vary. According to the recommendations for the use of super glue, the volatilization time will be determined in combination with the actual operation and construction spare parts. For example, when using dehydrated urea-formaldehyde adhesive and white latex, it is necessary to pressurize at room temperature of 25-30 ℃ for more than 12 hours.
    c.貼板:等干到不粘手市,將防火板小心地放到基板上面,如果粘貼的面積非常大,能用木條先間隔著放在基板上面,再將防火板放到基板上,等對正后再將木條抽出,將防火板一步步地按壓到基板上。然后用流滾輪或抹布用力壓勻,同時避免殘余的空氣在里面。
    C. Board pasting: when it is dry and not sticky, carefully put the fireproof board on the base plate. If the pasting area is very large, you can put the fireproof board on the base plate with wooden strips, and then put the fireproof board on the base plate. After aligning, pull out the wooden strips, and press the fireproof board on the base plate step by step. Then press evenly with a flow roller or rag, while avoiding residual air inside.
    d.修正:等以上的加壓工作做好了,就用修邊機或10度角之刃將多余的邊切去,后再用較利的銼刀將接縫銼得圓滑些。千萬注意:只能向下銼,不可來回銼,以免切斷面不平整光滑!多余而滲出來的膠應該用小塊抹布以及溶劑清理干凈。這樣整個施工過程就完成了。
    D. Correction: After the above pressurization work is completed, cut off the redundant edges with a trimming machine or a 10-degree angle blade, and then file the seams with a sharp file to make them smooth. Please note: only file down, not back and forth, to avoid uneven and smooth cutting section! Excess and leaked glue should be cleaned with small rags and solvent. So the whole construction process is completed.
    防火板
    e.施工環境要求:一般建議在現場施工將防火板和基板放在同一環境中48小時,濕度在45%,不宜高于80%,溫度不低于18攝氏度。
    E. Requirements for construction environment: It is generally recommended to put the fireproof board and base plate in the same environment for 48 hours, with the humidity of 45%, not higher than 80%, and the temperature not lower than 18 ℃.
    使用限制:
    Use restrictions:
    1.僅限室內使用、不適合直接附于水泥、混凝土墻、石膏板上;
    1. Only for indoor use, not suitable for direct attachment to cement, concrete wall and gypsum board;
    2.非結構性材料、應附于合適基材上;
    2. Non-structural materials shall be attached to the appropriate substrate;
    3.不宜長時間置于高于135攝氏度的場所或在直射陽光暴曬。
    3. It should not be placed in places higher than 135 ℃ for a long time or exposed to direct sunlight.
    選用的時候,可根據自己的尺寸和花色要求,由生產商進行加工。由于是貼面,防火板可以處理得很靈活,因此也會有很多的花色,讓我們有很大的挑選余地。更多相關內容就來我們網站http://www.kcrft.cn咨詢吧!
    When selecting, it can be processed by the manufacturer according to its own size and design requirements. Because of the veneer, the fireproof board can be handled flexibly, so there will also be a lot of decors, so we have a lot of choice. Come to our website for more relevant content http://www.kcrft.cn Ask!

    Related products相關產品

    聯系我們

    產品銷售熱線:13165128506

    技術方案咨詢:18560211715

    倉庫地址:山東省濟南市天橋區金鑫產業園303倉庫

    九江工廠:九江市江東大道3號

    臺灣新竹工廠:臺灣新竹

    泰國曼谷工廠:泰國曼谷

    關注我們
    山東創圖建筑裝飾工程有限公司 備案號:魯ICP備14019259號-2 網站地圖 XML TXT 魯公網安備37010502002020號

    截屏,微信識別二維碼

    微信號:13165128506

    在线视频成人一区二区-亚洲另类中文字幕在线| 国产美女裸露无遮挡双奶网站-国产精品色午夜视频免费看| 亚洲最新国产无人区123-黄片一区二区在线观看| 日韩精品人妻系列一区-亚洲女同性一区二区三区| 午夜精品午夜福利在线-内射无套内射国产精品视频| 亚洲永久免费在线观看-亚洲欧美导航一区二区导航| 三级a级一级大片在线观看-日韩av有码免费观看| 欧美日韩精品人妻在线-在线播放中文字幕一区| 欧美精品一区二区三区爽爽爽-日韩国产精品亚洲经典| 国产精品二区高清在线-91精品91久久久久久| 国产在线观看高清精品-四季av一区二区三区中文字幕| 欧美一级二级三级在线看-日韩精品欧美嫩草久久99| 精品亚洲卡一卡2卡三卡乱码-一区三区二插女人高潮在线观看| 在线成色中文综合网站-国产二区精品视频在线观看| 亚洲精品一区网站在线观看-黄页视频免费观看网站| 极品人妻av在线播放-久久精品视频一区二区三区| 国产精品v欧美精品v日韩精品-国产欧美日韩精品区一区二污污污| 欧美成人精品巨臀大屁股-亚洲综合欧美日韩一区| 五月婷婷免费观看视频-男人操女人下面视频在线免费看| 美女把腿张开给帅哥桶-无码无套少妇18p在线直播| 俄罗斯胖老太太黄色特级片-国产精品黑丝美腿美臀| 国模自慰一区二区三区-日韩一级黄色片天天看| 婷婷亚洲欧美综合丁香亚洲-超刺激国语对白在线视频| mm在线精品视频在线观看-欧美国产日韩在线一区二区三区| 中文字幕日韩精品不卡一区二区-成人av在线观看一区二区| 一区二区三区女同性恋-熟妇高潮一区二区高清网络视频| 日韩av电影一区二区网址-老熟妇仑乱视频一区二| 国产精品v欧美精品v日韩精品-国产欧美日韩精品区一区二污污污| 国产在线一区二区三区欧美-久久偷拍精品视频久久| 国产精品成人欧美激情-黄色床上完整版高清无遮挡| 久久精品人妻一区二区三区极品-久久99热这里只有精品免费| 国产精品美女在线网址-久草免费福利在线观看视频| 欧美日韩国产在线资源-超碰成人国产一区二区三区| 女主播啪啪大秀免费观看-精品99午夜福利影院| 人妻互换精品一区二区-夜夜爽一区二区三区视频| 亚洲欧美日韩二区三区-国产在线欧美一区日韩二区| 成人免费资源在线观看-欧美国产日韩高清在线综合| 国产一区二区三区噜噜-精品久久亚洲一区二区欧美| 日韩精品一区二区三区粉嫩av-欧美亚洲国产中文字幕| 丝袜美腿人妻连续中出-在线观看日韩三级视频| 精品少妇一区二区18-一区二区三区日韩在线播放|