Due to the fire board is a new industry in recent years, many users are not very familiar with the application of fireproof board. Today, fumihome explains the specific method for the use of fireproof board as partition wall.

　　使用的具體步驟：

　　The specific steps are as follows:

　　1．防火板材：一般情況下建議用6mm厚度以上的玻鎂板作隔墻板。

　　1. Fireproof board: in general, it is recommended to use glass magnesium plate with thickness above 6 mm as partition board.

　　2．配件：6mm以上的板材固定在框架龍骨上，要用3.5200mm的沉頭螺釘固定，釘頭低于板面0.5mm，以便保證飾面平整。

　　2. Accessories: the plate with a diameter of more than 6 mm is fixed on the frame keel with a 3.5200 mm countersunk screw. The nail head is 0.5 mm lower than the plate surface to ensure the smooth finish.

　　3．安裝：開始安裝時，必須標好龍骨的準確位置，并作好記號。豎龍骨距離為450-600mm，墻體的連接處和門窗兩側安裝時要裝附加龍骨，如墻體高度大于2440mm時，須在板材連接處加裝支撐龍骨。

　　3. Installation: at the beginning of installation, the accurate position of keel must be marked and marked. The center distance of vertical keel is 450-600mm. Additional keel shall be installed at the connection of wall and both sides of doors and windows. If the wall height is greater than 2440 mm, support keel shall be installed at the connection of plate.
                  

　　4．板距：相臨板材之間留縫距4-6mm，板材與地面之間必須留有5mm的間隙，螺釘安裝距為150mm，距板邊10mm，距離板角30mm。

　　4. Plate distance: the seam distance between adjacent plates is 4-6mm, the gap between plate and ground must be 5mm, the center distance of screw installation is 150 mm, the distance from plate edge is 10 mm, and the distance from plate angle is 30 mm.

　　5．吊掛：衛生間或廚房間等吊掛重物處，必須用木板或龍骨加固，以免板材受到破壞。

　　5. Hanging: the toilet or kitchen and other hanging heavy objects must be reinforced with wood or keel to avoid damage to the board.

　　6．接縫處理：在安裝時板材與板材留有間隙4-6mm，用107膠水或強力膠調勻后用刮刀涂抹板材及縫隙處，然后用紙帶或風格帶粘貼壓平。

　　6. Joint treatment: during installation, there is a gap of 4-6 mm between plates. After mixing with 107 glue or super glue, smear the plate and gap with scraper, and then paste and flatten with paper tape or style tape.

　　7．涂料裝飾：可以用噴涂、刷涂或滾涂，但刷涂時必須參看涂料的有關說明。

　　7. Coating decoration: spraying, brushing or rolling coating can be used, but the relevant instructions of coating must be referred to when brushing.

　　8．裝飾面貼瓷磚：在浴室、衛生間、廚房、地下室等潮濕區域安裝時，如需在板面貼瓷磚龍骨之間的距離必須縮短到400mm。墻體每隔三塊板(約3.6mm左右)必須留有一條伸縮縫。

　　8. Decorative surface tiles: when installing in the bathroom, bathroom, kitchen, basement and other humid areas, if it is necessary to paste tiles on the board, the distance between keel must be shortened to 400mm. There must be an expansion joint in the wall every three boards (about 3.6mm).

　　9．隔音墻體：如需墻體有較高的隔音效果，必須要求墻體和板材結合緊密密閉，再向空墻內填充礦棉，如龍骨兩面采用兩種不同厚度的板時，隔間效果更佳。

　　9. Sound insulation wall: if the wall is required to have high sound insulation effect, the wall and plate must be tightly sealed, and then the hollow wall is filled with mineral wool. For example, when two different thickness plates are used on both sides of the keel, the compartment effect is better.

　　10．抗沖擊墻體：建議您選用8mm以上的防火板或加一層板，第二張板須用長一些的螺絲釘加固。這種方法可增強抗沖擊、隔熱、隔音效果和防火性能。

　　10. Impact resistant wall: it is recommended that you select a fire-proof board above 8mm or add a layer of board. The second board must be reinforced with longer screws. This method can enhance shock resistance, heat insulation, sound insulation and fire resistance.

　　以上是關于防火板隔墻應用的方法介紹，想要了解更多內容歡迎點擊富美家http://www.kcrft.cn網站。

　　The above is about the fire prevention board partition wall application method introduction, want to know more content, welcome to click the rich Meijia http://www.kcrft.cn Website.