Doors are indispensable to every family and play an important role in our security. Therefore, the requirements for fire doors are always very strict. As a new type of fire doors, wooden doors are the product of high technology. Wooden fire doors can not only beautify our homes, but also increase our family safety. What are the attractive qualities of Fumeijia Fireproofing Board?

　　一、防火板具有豐富的表面紋理可供選擇，木紋素色金屬應有盡有。裝修時一定要考慮的是裝修一的風格，傳統的防火門不使用防火板，難以保證風格的統一性。所以當室內裝修使用一定紋理的表面紋理時，我們可以找與室內紋理相同的防火板來制作防火門，防火門銷售廠家說。

　　1. Fire-proof boards have abundant surface texture to choose from, and there are all kinds of lignin non-ferrous metals. When decorating, we must consider the style of decoration. Traditional fire doors do not use fire panels, so it is difficult to ensure the unity of style. So when the interior decoration uses a certain texture of the surface texture, we can find the same texture as the interior fireproof board to make the fireproof door, the fire door vendor said.

　　二、富美家防火板可阻燃防潮、防蟲、施工簡單、不褪色、無甲醛。

　　2. Fumeijia fire-proof board is flame-retardant, moisture-proof, insect-proof, simple in construction, non-fading and formaldehyde-free.

　　防火門安裝要點:

　　Installation points of fire door:

　　(1)線。根據設計要求的尺寸、高程和方向，畫出木門防火門框的位置線。

　　(1) Line. According to the design requirements of size, elevation and direction, draw the position line of wood door fire door frame.

　　(2)站立門框。先拆下木質防火板門框下的固定板，每一門框內的高度大于門扇的高度30毫米以上的人，洞口兩側地面必須設置預留槽。門框一般在±0.00標高以下埋設20mm?？蚩诘纳稀⑾鲁叽鐟?yīng)相同。允許誤差< 1.5mm，對角線誤差< 2mm。將木制防火門框用木楔臨時固定在孔內，經校準后，固定木楔、門框鐵腳與預埋鐵板件焊接牢固。

　　(2) Standing doorframe. Firstly, remove the fixing board under the wooden fire-proof board door frame. For people whose height in each door frame is higher than the height of the door fan over 30 mm, reserved grooves must be set on the ground on both sides of the opening. The doorframe is usually buried below (+0.00) elevation by 20mm. The upper and lower dimensions of the frame mouth shall be the same. The allowable error is less than 1.5 mm and the diagonal error is less than 2 mm. The wooden fireproof door frame is temporarily fixed in the hole with a wooden wedge. After calibration, the fixed wooden wedge, the iron foot of the door frame and the embedded iron plate are firmly welded.

　　(3)安裝門及附件。門框周圍的木質防火板裂縫，應保證用1:2水泥砂漿或強度不小于10MPa的細石混凝土密植，與墻體形成整體;固化后，對孔、壁進行噴涂。涂裝完畢后，安裝門扇、五金配件及相關防火裝置。門關閉后，門縫應均勻平整，打開自由攜帶，不得有過緊、過松和回彈現象。

　　(3) Installation doors and accessories. The cracks in the wood fireproof board around the door frame should be guaranteed to be closely planted with 1:2 cement mortar or fine stone concrete with strength not less than 10 MPa, forming an integral whole with the wall; after solidification, the holes and walls should be sprayed. After finishing painting, install doors and fans, hardware fittings and related fire protection devices. After the door closes, the door seam should be even and smooth, open and carry freely, and should not be too tight, too loose and springback phenomenon.

　　以上是富美家防火板廠家為大家整理的相關內容，想要了解更多內容，歡迎訪問網站：http://www.kcrft.cn

　　Above is the relevant content of Fumeijia Fireproofing Board Manufacturer for you. For more information, please visit the website: http://www.kcrft.cn.