山東創圖建筑裝飾工程有限公司
13165128506
您當前位置: 抗倍特板件拼接時應掌握幾點
來源：http://www.kcrft.cn/ 日期：2022-11-16 發布人：admin
抗倍特板這種材料雖然大家都認識了，但可能還不是很清楚其中的注意事項，下面富美家抗倍特廠家就來給大家普及一下抗倍特板件拼接時應掌握幾點。
Although we all know this material, we may not be very clear about the precautions. Now, Fumeijia Anti Beite Factory will popularize some points that should be mastered when splicing anti Beite plates.
a.粘合劑的涂布量應控制在2.5-3.0g/cm2，粘接表面要全部涂布到；
a. The coating amount of adhesive shall be controlled at 2.5-3.0g/cm2, and the bonding surface shall be completely coated;
b.拼接后用夾子夾緊30分鐘左右。豎直方向粘合時一定要開口，使粘合面增大，以確保粘合強度；
b. Clamp for about 30 minutes after splicing. When bonding in the vertical direction, an opening must be made to increase the bonding surface to ensure the bonding strength;
c.一旦發現被粘合部件有爆口等缺陷應將光滑平整的一面朝外，以保證粘合質量。
c. Once it is found that the bonded parts have defects such as cracks, the smooth and flat side shall be outward to ensure the bonding quality.
此外抗倍特板在安裝結束時如表面出現斑點或污跡，可用毛巾沾取少量油性清潔劑（油與丙酮的混合物）輕輕擦拭這些斑點或污點即可除去。如果沒有斑點或污跡用一般清潔劑如肥皂加水，或洗潔精加水擦拭便可。
In addition, if there are spots or stains on the surface of the anti magnification special plate at the end of installation, the spots or stains can be removed by gently wiping them with a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel. If there are no spots or stains, use a general cleaner such as soap and water, or detergent and water to wipe.
在加工邊緣時普遍采用的工具是手提鏤銑機。在進行作業前應清除板件表面的灰塵或異物，以免在板件表面留下劃痕或刻痕。
Handheld router is widely used to process edges. Before operation, the dust or foreign matters on the surface of the panel shall be removed to avoid scratches or nicks on the surface of the panel.
鏤銑機的加工速度應保持在2m/min為宜，如果鏤銑刀刀刃角度較小而工件厚度又較厚時，鏤銑機的加工速度應適當放慢。
The processing speed of the router should be kept at 2m/min. If the cutting edge angle of the router is small and the thickness of the workpiece is thick, the processing speed of the router should be appropriately slowed down.
另外銑刀刃的長度應大于加工件的厚度，以保證一次走刀能銑削出邊緣的線型。走刀時鏤銑刀應從高處逐步向低處下滑直至鏤銑刀刃包容銑削邊緣。
In addition, the length of the milling blade shall be greater than the thickness of the workpiece, so as to ensure that the line shape of the edge can be milled at one time. When cutting, the router should gradually slide down from the high to the low until the router edge contains the milling edge.
值得注意的是，走刀時一定要保持平穩，不要讓鏤銑機晃動。晃動會使工件的邊緣形成不規則波紋，給后道砂磨拋光工序增加工作量，影響加工效率。
It is worth noting that the cutter must be moved steadily, and the router must not shake. Shaking will cause irregular ripples on the edge of the workpiece, which will increase the workload of the subsequent sanding and polishing process and affect the processing efficiency.
抗倍特板件拼接時應掌握的要點就講解到這里了，您對此有什么需求或者問題就來我們網站http://www.kcrft.cn咨詢看看吧！
So far are the key points that should be mastered when splicing the anti multiplier panels. If you have any needs or problems, please come to our website http://www.kcrft.cn Consult!
分類導航
相關新聞
Related products相關新聞
產品銷售熱線：13165128506
技術方案咨詢：18560211715
倉庫地址：山東省濟南市天橋區金鑫產業園303倉庫